SEKURE DGP2-641 Manual de Instalação descarregar pdf (Página 34)

32 R

EFERENCE

& I

NSTALLATION

ANUAL

9.11 A

UTO

EST

EPORT

The control panel can transmit the test report code programmed into

section [3902] every hour (Hourly Test Transmission) or after a period of

time (Auto Test Report Period).

9.12 D

ISARM

EPORTING

PTIONS

(Default = disabled) When option [7] is disabled, the control panel sends

the Disarming Report Codes (see section 9.2) every time the partition is

disarmed. When option [7] is enabled, the control panel sends the

Disarming Report Codes to the Monitoring Station only when the partition is

disarmed following an alarm. Select the section that corresponds to the

desired partition and enable or disable option [7]:

9.13 Z

ONE

ESTORE

EPORT

PTIONS

(Default = disabled) When option [8] is disabled, the control panel sends

the Zone Alarm Restore report codes to the Monitoring Station when the

Bell Cut-Off Timer elapses (see section 8.2) or when the alarm is disarmed.

When option [8] is enabled, the control panel sends the Zone Alarm

Restore report codes (see section 9.2) to the Monitoring Station as soon as

the zone returns to normal (zone closure) or upon disarming.

9.14 A

UTO

EPORT

ODE

ROGRAMMING

When using either the Contact ID or SIA Reporting Formats (see section

9.6), the control panel can automatically program a set of default report

codes. However, the Contact ID Reporting Format can be modified using

the manual programming method (see section 9.6.3 & section 9.6.4) to

program remaining report codes or to change some of the defaults. From

programming mode (see section 4.4) enter any of the following sections to

set the indicated report codes with the default values (FF) from the

Automatic Report Codes List in the Programming Guide:

Option Feature Description

[3] [4]

OFF OFF

Auto Test

Report

Period

(default)

After the number of days (000 to 255, default =

000) programmed into section [3040] elapse, the

control panel can transmit the report code at the

time (00:00 to 23:59, default = 00:00)

programmed into section [3041].

ON OFF

Hourly Test

Transmission

The control panel transmits the test report code at

the same time every hour. Program the minute of

each hour (00:00 to 00:59, default = 00:00) when

the test report should be sent into section [3041].

ON ON

Timed Test

Transmission

when Armed/

Disarmed

When armed:

The control panel transmits the test report code at

regular intervals while the partition is armed.

Program the number of minutes (000 to 255,

default 005) between each transmission in

section [3042].

When disarmed:

The control panel transmits the test report code at

regular intervals while the partition is disarmed.

Program the number of minutes (000 to 255,

default = 060) between each transmission in

section [3043].

Partition 1: [3123] Partition 3: [3323] Partition 5: [3523] Partition 7: [3723]

Partition 2: [3223] Partition 4: [3423] Partition 6: [3623] Partition 8: [3823]

Section Description

[4030] Resets all the report code sections to 00 (cleared).

[4031] Sets all the report code sections to FF (defaults).

Section Sets to Defaults (FF) Reset Sections

[4032]

Zone Alarm and Restore Report Codes

Tamper and Restore Report Codes

[0201] to [0296]

[4033]

Keyswitch Arming Report Codes

Keyswitch Disarming Report Codes

Access Code Arming Report Codes

Access Code Disarming Report Codes

[0701] to [0732]

[0801] to [0832]

[2001] to [2099]

[2101] to [2199]

[4034] Special System Report Codes [3900] to [3909]

[4035]

Special Arming Report Codes

Special Disarming Report Codes

[3910] to [3919]

[3920] to [3929]

[4036] Special Alarm Report Codes [3930] to [3939]

[4037] Trouble and Restore Report Codes [3940] to [3991]

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 65 66

Comentários a estes Manuais

Sem comentários

SEKURE DGP2-641 Manual de Instalação Página 34

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso SEKURE DGP2-641