SEKURE DGP2-641 Manual do Utilizador descarregar pdf (Página 6)

Digiplex & DigiplexNE - 39 - Modules Programming Guide

Appendix 1: Programming PGMS

A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event occurs in the system. For

example, a PGM can be used to reset smoke detectors, activate strobe lights, open/close garage doors and much more. When a PGM closes, the module

supplies a ground to the PGM (transistor PGM), or the link between N.C. and COM is established (Relay PGM), which activates any device or relay

connected to it. When a PGM opens, the circuit opens from ground (transistor PGM), or the link between N.O. and COM is established, therefore no power

is provided to the devices connected to it.

PGM ACTIVATION EVENT

The PGM Activation Event determines which event from what source will activate the PGM. The Event Group specifies the event, the Feature Group

identifies the source, and the Start # and End # sets the range within the Feature Group (see PGM Programming Table below).

For example, the APR3-PGM4 (See “4-PGM Expansion Module” on page 15) can activate PGM1 when the partition is armed by User Access Codes 256 to

260. Therefore:

Event Group section [004] = 010 “Arming with User Code”

Feature Group section [005] = 001 “User Codes 256 to 511”

Start # section [006] = 000 (representing user code 256)

End # section [007] = 004 (representing user code 260)

Enter the sections that correspond to the Event Group, Feature Group, Start # and End # of the desired PGM and enter the data as required.

PGM DEACTIVATION OPTION

Once the PGMs are activated, they can deactivate when another event occurs or after a period of time. The PGM Deactivation Option determines which

method is used, the PGM Deactivation Event or the PGM Timer. Enter the section that corresponds to the desired PGM and enable or disable the option.

PGM DEACTIVATION EVENT

When the PGM Deactivation Option (see above) is disabled, the PGM Deactivation Event determines which event from what source will return the PGM to

its original state. The Event Group specifies the event, the Feature Group identifies the source, and the Start # and End # determine the range within the

Feature Group. The complete PGM Programming Table appears below.

For example, the APR3-PGM4 (See “4-PGM Expansion Module” on page 15) can deactivate PGM1 when zone 3 opens. Therefore:

Event Group section [008] = 001 “Zone is Open”

Feature Group section [009] = 000 “Zone Numbers”

Start # section [010] = 003

End # section [011] = 003

Enter the sections that correspond to the Event Group, Feature Group, Start # and End # of the desired PGM and enter the data as required.

PGM PROGRAMMING TABLE

Event Group Feature Group Start # End #

PGM Activation Event PGM __/__/__ __/__/__ __/__/__ __/__/__

PGM Deactivation Event PGM __/__/__ __/__/__ __/__/__ __/__/__

Event Group Event Feature Group Feature Start # End #

000 Zone is OK

000

255 = any Zone #

Zone Numbers

001 to 096 001 to 096

001 Zone is Open 001 to 096 001 to 096

002 Zone is Tampered 001 to 096 001 to 096

003 Zone is in Fire Loop Trouble 001 to 096 001 to 096

004 Non-reportable Event

000

TLM Trouble (see NOTE 3 on page 45) 000 000

Smoke detector reset 001 001

Arm with no entry delay 002 002

Arm in Stay mode 003 003

Arm in Away mode 004 004

Full arm when in Stay mode 005 005

Voice module access 006 006

Remote control access 007 007

PC Fail to communicate 008 008

Midnight 009 009

1 2 3 4 5 6 7 8 9 10 11 12 13

Comentários a estes Manuais

Sem comentários

SEKURE DGP2-641 Manual do Utilizador Página 6

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso SEKURE DGP2-641